Changes

added feedback cover and front bearing information
Line 57: Line 57:     
Cable plug: MS-3106E-22-14S
 
Cable plug: MS-3106E-22-14S
 +
 +
=== Feedback Cover ===
 +
 +
==== EB-40x-x-11 ====
 +
 +
On the inside of the plastic cap that covers the feedback area of the motor, there is a boss with an O-ring to seal against a bore in the main body of the motor:
 +
 +
* 101.4mm OD boss mating with a 104mm final ID tapered step-down
 +
* 105mm with O-rings installed?
 +
* O-rings measured ~1.7mm thick
 +
 +
Possible replacements:
 +
 +
[https://www.mcmaster.com/1302N129/ Oil-Resistant Buna-N O-Ring, 1.5 mm Wide, 100 mm ID | McMaster-Carr]
 +
 +
[https://www.mcmaster.com/9262K716/ Oil-Resistant Buna-N O-Ring, 2 mm Wide, 100 mm ID | McMaster-Carr]
 +
 +
[https://www.mcmaster.com/9262K868/ Oil-Resistant Buna-N O-Ring, 2 mm Wide, 102 mm ID | McMaster-Carr]
 +
 +
=== Bearings ===
 +
 +
==== EB-40x-x-11 ====
 +
 +
Output shaft side bearing marked:
 +
 +
<pre>PEER CHINA 6005Z</pre>
 +
 +
* 47mm OD
 +
* 25mm ID
 +
* ~12mm thick
 +
* double shielded
 +
 +
A compatible replacement:
 +
 +
[https://www.mcmaster.com/6661K18/ Ball Bearing, Shielded, Trade No. 6005-2Z, for 25 mm Shaft Diameter | McMaster-Carr]
 +
 +
There is a 52mm OD 47mm ID ~2.5mm (2.4 - 2.7?) thick O-ring to seal the outer race of the bearing against the bore it's pressed into, similar to this:
 +
 +
[https://www.mcmaster.com/9262K736/ Oil-Resistant Buna-N O-Ring, 2.5 mm Wide, 47 mm ID | McMaster-Carr]
 +
 +
The bearing is pressed into the front face plate on the motor. This plate has an O-ring to seal a boss into a mating bore with a ~110.5mm final ID tapered step-down. That boss has a 108.5mm outer diameter, and the O-ring is ~2mm thick. The following might be suitable replacements:
 +
 +
[https://www.mcmaster.com/9262K874/ Oil-Resistant Buna-N O-Ring, 2 mm Wide, 109 mm ID | McMaster-Carr]
 +
 +
[https://www.mcmaster.com/9262K327/ Oil-Resistant Buna-N O-Ring, 3 mm Wide, 108 mm ID | McMaster-Carr]
 +
 +
There is supposed to be an oil seal in the 35mm diameter 7mm diameter bore in the lip retaining the front bearing. It should seal onto the 24.6mm shoulder on the shaft. Here are some possible replacements:
 +
 +
[https://www.mcmaster.com/1199N14/ Spring-Loaded Rotary Shaft Seal with Wiper Lip, for 25 mm Shaft Diameter and 35 mm Diameter x 7.3 mm Wide Bore | McMaster-Carr]
 +
 +
[https://www.mcmaster.com/5154T66/ Spring-Loaded Rotary Shaft Seal, for 25 mm Shaft Diameter, 25 mm ID x 35 mm OD | McMaster-Carr]
    
== Online Resources ==
 
== Online Resources ==