Kollmorgen Goldline Series Servo Motors: Difference between revisions

(2 intermediate revisions by the same user not shown)

Line 97:

[https://www.mcmaster.com/9262K736/ Oil-Resistant Buna-N O-Ring, 2.5 mm Wide, 47 mm ID | McMaster-Carr]

The bearing is pressed into the front face plate on the motor. This plate has an O-ring to seal a boss into a mating bore with a ~110.5mm final ID tapered step-down. That boss has a 108.5mm outer diameter, and the O-ring is ~2mm thick. The following might be suitable replacements:

The bearing is pressed into the front face plate on the motor, a casting embossed C-64180-4 and with C-64135 written in permanent marker (for the bearing?). This plate has an O-ring to seal a boss into a mating bore with a ~110.5mm final ID tapered step-down. That boss has a 108.5mm outer diameter, and the O-ring is ~2mm thick. The following might be suitable replacements:

[https://www.mcmaster.com/9262K874/ Oil-Resistant Buna-N O-Ring, 2 mm Wide, 109 mm ID | McMaster-Carr]

Line 108:

[https://www.mcmaster.com/5154T66/ Spring-Loaded Rotary Shaft Seal, for 25 mm Shaft Diameter, 25 mm ID x 35 mm OD | McMaster-Carr]

=== Locknut ===

==== EB-40x-x-11 ====

The locknut that secures the resolver to the shaft is marked "KM-04", similar to this:

[https://www.mcmaster.com/3554N15/ Carbon Steel Bearing Retaining Nut, Chamfered Face, M20 x 1 mm Thread Size | McMaster-Carr]

=== Snap Rings ===

==== EB-40x-x-11 ====

External retaining rings that go into grooves on the 25mm shaft, serving as a shoulder for the bearings to bottom out on:

[https://www.mcmaster.com/98541A440/ External Retaining Ring, for 25 mm OD, Black-Phosphate 1060-1090 Spring Steel | McMaster-Carr]

== Online Resources ==

@@ Line 97: / Line 97: @@
 [https://www.mcmaster.com/9262K736/ Oil-Resistant Buna-N O-Ring, 2.5 mm Wide, 47 mm ID | McMaster-Carr]
-The bearing is pressed into the front face plate on the motor. This plate has an O-ring to seal a boss into a mating bore with a ~110.5mm final ID tapered step-down. That boss has a 108.5mm outer diameter, and the O-ring is ~2mm thick. The following might be suitable replacements:
+The bearing is pressed into the front face plate on the motor, a casting embossed C-64180-4 and with C-64135 written in permanent marker (for the bearing?). This plate has an O-ring to seal a boss into a mating bore with a ~110.5mm final ID tapered step-down. That boss has a 108.5mm outer diameter, and the O-ring is ~2mm thick. The following might be suitable replacements:
 [https://www.mcmaster.com/9262K874/ Oil-Resistant Buna-N O-Ring, 2 mm Wide, 109 mm ID | McMaster-Carr]
@@ Line 108: / Line 108: @@
 [https://www.mcmaster.com/5154T66/ Spring-Loaded Rotary Shaft Seal, for 25 mm Shaft Diameter, 25 mm ID x 35 mm OD | McMaster-Carr]
+=== Locknut ===
+==== EB-40x-x-11 ====
+The locknut that secures the resolver to the shaft is marked "KM-04", similar to this:
+[https://www.mcmaster.com/3554N15/ Carbon Steel Bearing Retaining Nut, Chamfered Face, M20 x 1 mm Thread Size | McMaster-Carr]
+=== Snap Rings ===
+==== EB-40x-x-11 ====
+External retaining rings that go into grooves on the 25mm shaft, serving as a shoulder for the bearings to bottom out on:
+[https://www.mcmaster.com/98541A440/ External Retaining Ring, for 25 mm OD, Black-Phosphate 1060-1090 Spring Steel | McMaster-Carr]
 == Online Resources ==