Saftronics GP5 VFDs: Difference between revisions

(8 intermediate revisions by the same user not shown)

Line 54:

| MODBUS parity selection

|}

NOTE: the numbering of some parameters above <code>n100</code> seem to be slightly shifted between different revisions of the VFD firmware. A physical Saftronics GP5/FP5 Series Instruction Manual (PN 027-2005, Rev 1195, 1995) differs from the "027-2005F" that can be found online.

=== Modbus registers ===

Line 62:

Line 64:

* [https://www.yaskawa.com/delegate/getAttachment?documentId=TM4026&cmd=documents&documentName=TM4026.pdf#page=41 Page 41] (7-8 in the PDF) of the RTU manual lists the "Drive Parameter" (read/write) registers.

* [https://www.yaskawa.com/delegate/getAttachment?documentId=TM4026&cmd=documents&documentName=TM4026.pdf#page=53 Page 53] (7-20 in the PDF) of the RTU manual lists the "Special" (read/write) registers.

{| class="wikitable"

! Address Hex

! Parameter No.

! Description

|-

| 0x0000- 0x000a

|

| Command registers (read/write) for broadcasts, first two are Simultaneous broadcast registers (write-only)

|-

| 0x0020- 0x0040

|

| Monitor registers (read-only)

|-

| 0x0101- 0x018d

| n101- n241?

| Parameters (the max parameter is supposed to be n116...)

|}

=== mbpoll ===

~~<code>~~mbpoll~~</code> commands~~:

There is an open source utility that can speak Modbus over a serial port (or USB to serial) that has an RS-485 adapter attached. It's called mbpoll:

<pre># fault reset

https://github.com/epsilonrt/mbpoll

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:~~int~~ -- 8

<code>mbpoll</code> commands to interact with the VFD:

<pre># trigger external fault

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 4

# fault reset

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 8

# stop

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 0

# set forward run

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:~~int~~ -- 1

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 1

# set reverse run

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:~~int~~ -- 3

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 3

# set the output frequency (Hz*10, 1003 means 100.3Hz)

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 2 -t 4:~~int~~ -- 1000

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 2 -t 4:int16 -- 1000

# monitor status

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 0x20

# monitor drive fault

./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 0x21

# monitor frequency command (Hz*10, 1003 means 100.3Hz)

Line 90:

Line 126:

== Online Resources ==

<del>[http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual]</del> (DEAD)

[http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual]

[https://web.archive.org/web/20150513231041/http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual] (Wayback Machine)

[https://www.yaskawa.com/delegate/getAttachment?documentId=TM4506&cmd=documents&openNewTab=true&documentName=TM4506.pdf Yaskawa GPD 506/P5 Technical Manual (TM4506)]

Line 98:

Line 136:

[https://www.manualslib.com/download/1257334/Yaskawa-Gpd-506-P5.html Yaskawa GPD 506 / Modbus RTU Technical Manual] (alternate, must complete captcha)

[https://www.yaskawa.com/delegate/getAttachment?documentId=PP.P5G5.03.Troubleshoot&cmd=documents&documentName=PP.P5G5.03.Troubleshoot.pdf Yaskawa GPD 506/P5 and GPD 515/G5 Unit Troubleshooting Manual Section Three: Fault Codes & Appendix (PP.P5G5.03.Troubleshoot, Rev. 06/11/2003)]

[https://www.yaskawa.com/delegate/getAttachment?documentId=TOE-C736-40.15&cmd=documents&documentName=TOE-C736-40.15%20SI-K2P%20Instruction%20Manual.pdf Yaskawa Varispeed-616PC5/P5 Option Card RS-232C/485 Interface Card SI-K2/P Instructions (TOE-C736-40.15)]

@@ Line 54: / Line 54: @@
 | MODBUS parity selection
 |}
+NOTE: the numbering of some parameters above <code>n100</code> seem to be slightly shifted between different revisions of the VFD firmware. A physical Saftronics GP5/FP5 Series Instruction Manual (PN 027-2005, Rev 1195, 1995) differs from the "027-2005F" that can be found online.
 === Modbus registers ===
@@ Line 62: / Line 64: @@
 * [https://www.yaskawa.com/delegate/getAttachment?documentId=TM4026&cmd=documents&documentName=TM4026.pdf#page=41 Page 41] (7-8 in the PDF) of the RTU manual lists the "Drive Parameter" (read/write) registers.
 * [https://www.yaskawa.com/delegate/getAttachment?documentId=TM4026&cmd=documents&documentName=TM4026.pdf#page=53 Page 53] (7-20 in the PDF) of the RTU manual lists the "Special" (read/write) registers.
+{| class="wikitable"
+! Address Hex
+! Parameter No.
+! Description
+|-
+| 0x0000-<br/>0x000a
+|
+| Command registers (read/write) for broadcasts, first two are Simultaneous broadcast registers (write-only)
+|-
+| 0x0020-<br/>0x0040
+|
+| Monitor registers (read-only)
+|-
+| 0x0101-<br/>0x018d
+| n101-<br/>n241?
+| Parameters (the max parameter is <i>supposed</i> to be n116...)
+|}
 === mbpoll ===
-<code>mbpoll</code> commands:
+There is an open source utility that can speak Modbus over a serial port (or USB to serial) that has an RS-485 adapter attached. It's called mbpoll:
-<pre># fault reset
+https://github.com/epsilonrt/mbpoll
-./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:int -- 8
+<code>mbpoll</code> commands to interact with the VFD:
+<pre># trigger external fault
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 4
+# fault reset
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 8
+# stop
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 0
 # set forward run
-./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:int -- 1
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 1
 # set reverse run
-./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 1 -t 4:int -- 3
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 1 -t 4:int16 -- 3
 # set the output frequency (Hz*10, 1003 means 100.3Hz)
-./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 2 -t 4:int -- 1000
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -W -0 -r 2 -t 4:int16 -- 1000
+# monitor status
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 0x20
+# monitor drive fault
+./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P even -a 1 -0 -r 0x21
 # monitor frequency command (Hz*10, 1003 means 100.3Hz)
@@ Line 90: / Line 126: @@
 == Online Resources ==
+<del>[http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual]</del> (DEAD)
-[http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual]
+[https://web.archive.org/web/20150513231041/http://www.efesotomasyon.com/html/control_techniques/027-2005F%20GP5%20Manual.pdf Saftronics FP5/GP5 Series User's Manual] (Wayback Machine)
 [https://www.yaskawa.com/delegate/getAttachment?documentId=TM4506&cmd=documents&openNewTab=true&documentName=TM4506.pdf Yaskawa GPD 506/P5 Technical Manual (TM4506)]
@@ Line 98: / Line 136: @@
 [https://www.manualslib.com/download/1257334/Yaskawa-Gpd-506-P5.html Yaskawa GPD 506 / Modbus RTU Technical Manual] (alternate, must complete captcha)
+[https://www.yaskawa.com/delegate/getAttachment?documentId=PP.P5G5.03.Troubleshoot&cmd=documents&documentName=PP.P5G5.03.Troubleshoot.pdf Yaskawa GPD 506/P5 and GPD 515/G5 Unit Troubleshooting Manual Section Three: Fault Codes & Appendix (PP.P5G5.03.Troubleshoot, Rev. 06/11/2003)]
 [https://www.yaskawa.com/delegate/getAttachment?documentId=TOE-C736-40.15&cmd=documents&documentName=TOE-C736-40.15%20SI-K2P%20Instruction%20Manual.pdf Yaskawa Varispeed-616PC5/P5 Option Card RS-232C/485 Interface Card SI-K2/P Instructions (TOE-C736-40.15)]