CNC Wiki

Folinn H1 Series VFDs: Difference between revisions

← Older edit
added MODBUS register address scheme notes
added more parameters to enable MODBUS timeout fault
 
(8 intermediate revisions by the same user not shown)
Line 19: Line 19:
== Model Numbers ==
== Model Numbers ==


* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme
In the FoLinn H1 series manual:
 
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme
 
In the LinsVFD EV50 series manual:
 
* [https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme


== Wiring Diagram ==
== Wiring Diagram ==


* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=7 Page 7] (10 in the PDF) shows the power wiring
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=7 Page 7] (10 in the PDF) shows the power wiring
* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=67 Page 67] (129 in the PDF) shows the H0101 interface panel screw terminal / RJ45 pinout
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=67 Page 67] (129 in the PDF) shows the H0101 interface panel screw terminal / RJ45 pinout
* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=68 Page 68] (132 in the PDF) shows the H0110 interface panel screw terminal / RJ45 pinout
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=68 Page 68] (132 in the PDF) shows the H0110 interface panel screw terminal / RJ45 pinout
* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=72 Page 72] (139 in the PDF) shows the H0100 interface panel screw terminal pinout
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=72 Page 72] (139 in the PDF) shows the H0100 interface panel screw terminal pinout
* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=73 Page 73] (142 in the PDF) shows the H0200 interface panel screw / RJ45 / D-Sub? terminal pinout
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=73 Page 73] (142 in the PDF) shows the H0200 interface panel screw / RJ45 / D-Sub? terminal pinout
* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=76 Page 76] (147 in the PDF) shows the H0201 interface panel screw / RJ45 / D-Sub? terminal pinout
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=76 Page 76] (147 in the PDF) shows the H0201 interface panel screw / RJ45 / D-Sub? terminal pinout
 
NOTE: <del>they claim that pins 1 &amp; 2 on the RJ45 are RS-485+/-</del>, but in reality it's reversed and pins 8 &amp; 7 are RS-485+/- and pins 1 &amp; 2 are +5V &amp; GND respectively.


NOTE: they claim that pins 1&amp;2 on the RJ45 are RS-485+/-, but in reality it's reversed and pins 8&amp;7 are RS-485+/- and pins 2&amp;4 are GND.
=== RS-485 ===
 
{| class="wikitable"
! RJ45 Pin
! Function
|-
| 1
| +5V
|-
| 2
| GND
|-
| 3
| +12V
|-
| 7
| RS-485 B-
|-
| 8
| RS-485 A+
|}


== Dimensions ==
== Dimensions ==


* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
In the FoLinn H1 series manual:
 
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
 
In the LinsVFD EV50 series manual:
 
* [https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
 
== Parameters ==
 
{| class="wikitable"
! Parameter No.
! Default Value
! Range
! Description
|-
| P02.18
| 50.000 Hz
| 0.000 - 99999.000 Hz
| Maximum setting value
|-
| P02.19
| 0.000 Hz
| 0.000 - 99999.000 Hz
| Minimum setting value
|-
| P02.50
|
| 0.050 - 3600.000 s
| Acceleration time 0
|-
| P02.70
|
| 0.050 - 3600.000 s
| Deceleration time 0
|-
| P05.08
| 55.000 Hz
| -1020.000 - 1020.000 Hz
| Motor upper frequency limit
|-
| P06.00
|
| 0: off<br/>1: complete<br/>2: simple
| Motor parameter self-learning
|-
| P06.10
| 0: asynchronous
| 0: asynchronous<br/>1: surface mount permanent magnet synchronous<br/>2: salient pole permanent magnet synchronous<br/>4: single-phase motor
| Motor type
|-
| P06.05
|
| 2-16 kHz
| Carrier frequency
|-
| P06.11
|
| 0.000 - 100000.000 kW
| Motor rated power
|-
| P06.12
|
| 0 - 1000 V
| Motor rated voltage
|-
| P06.13
|
| 1 - 3000 Hz
| Motor rated frequency
|-
| P06.14
|
| 0.00 - 1000.00 A
| Motor rated current
|-
| P06.15
|
| 10 - 65535 RPM
| Motor rated speed
|-
| P06.16
|
| 0.00 - 1.00 (ratio)
| Motor power factor
|-
| P06.17
|
| 2 - 100 poles (not pairs)
| Motor pole count
|-
| P06.18
|
| 0.1 - 10000.0 Nm
| Motor rated torque
|-
| P06.19
|
| 0.00 - 1000.00 A
| Motor no-load current
|-
| P06.20
|
| 1.000 - 10000.000 mV/RPM
| PM motor back EMF/rev
|-
| P06.40
|
| 0.000 - 99.990 ohms
| Stator impedance
|-
| P06.41
|
| 0.000 - 99.990 ohms
| Rotor impedance
|-
| P06.42
|
| 0.000 - 999.990 mH
| Stator leakage reactance
|-
| P06.44
|
| 0.00 - 999.90 mH
| Motor main reactance
|}
 
== Alarm Codes ==
 
* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=63 Page 63] (122 in the PDF) shows a list of fault codes


== Modbus control ==
== Modbus control ==
Line 150: Line 307:
| 2: communication (?)
| 2: communication (?)
| Pause command source
| Pause command source
|}
To configure MODBUS timeout:
{| class="wikitable"
! Parameter No.
! Default Value
! Required Value
! Description
|-
| P01.30
| 0000
| 1340: Comparator 1 Output
| Virtual terminal setting
|-
| P03.08
| 00: no effect
| 17: use P01.30 bit 0 (in single command mode)
| Fault command source
|-
| P12.00
| 0.0
| 2.0 (seconds until timeout)
| Free parameter 1
|-
| P16.00
| 0000: invalid?
| 1044: use P10.44 "communication timeout"
| Comparator 1 input parameter selection
|-
| P16.01
| 0000: invalid
| 1200: use P12.00 "free parameter 1"
| Comparator 1 comparison parameter selection
|-
| P16.02
| 0: &gt; (greater than)
| 2: &ge; (greater than or equal to)
| Comparator 1 configuration
|}
|}


Line 324: Line 520:
=== mbpoll ===
=== mbpoll ===


== PDFs ==


[[Media:FoLinn_H1_Series_Inverter_User_Manual.pdf]]


== Online Resources ==
== Online Resources ==


[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf H1 Series Inverter User Manual (2021.V1.0)] (StepperOnline)
[https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf H1 Series Inverter User Manual (2021.V1.0)] (StepperOnline, no FoLinn mentioned)


[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Easy_User_Manual.pdf H1 Series Inverter Simple Manual] (StepperOnline)
[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Easy_User_Manual.pdf H1 Series Inverter Simple Manual] (StepperOnline, no FoLinn mentioned)
 
[https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf LinsVFD EV50 Series Inverter Full User Manual] (LinsVFD on StepperOnline, no FoLinn mentioned)
 
[https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Easy_User_Manual.pdf LinsVFD EV50 Series Inverter Easy User Manual] (LinsVFD on StepperOnline, no FoLinn mentioned)


[https://www.chinafolinn.com/uploads/image/20201021/5f8f9c43a68b0.pdf H1 Series Inverter Simple Manual (2020.10.21)] (Folinn)
[https://www.chinafolinn.com/uploads/image/20201021/5f8f9c43a68b0.pdf H1 Series Inverter Simple Manual (2020.10.21)] (Folinn)
Line 336: Line 538:
[https://www.chinafolinn.com/uploads/image/20200602/5ed61f05888f9.pdf H1 Series Compact Inverter Brochure (2020.06.02)] (Folinn)
[https://www.chinafolinn.com/uploads/image/20200602/5ed61f05888f9.pdf H1 Series Compact Inverter Brochure (2020.06.02)] (Folinn)


https://cononmotor.com.au/wp-content/uploads/2022/05/2.29.182-H1-Detailed-Manual-%E8%8B%B1%E6%96%87%E7%89%88%E8%AF%A6%E7%BB%86%E8%AF%B4%E6%98%8E%E4%B9%A61.pdf
[https://cononmotor.com.au/wp-content/uploads/2022/05/2.29.182-H1-Detailed-Manual-%E8%8B%B1%E6%96%87%E7%89%88%E8%AF%A6%E7%BB%86%E8%AF%B4%E6%98%8E%E4%B9%A61.pdf 2.29.182-H1-Detailed-Manual-英文版详细说明书1.pdf]
 
[https://cononmotor.com.au/wp-content/uploads/2020/03/H1-Simple-User-Manual-Revised.pdf H1-Simple-User-Manual-Revised.pdf]


https://cononmotor.com.au/wp-content/uploads/2020/03/H1-Simple-User-Manual-Revised.pdf
[https://www.omc-stepperonline.com/linsvfd LinsVFD Variable Frequency Drives] (now LinsVFD branded instead of StepperOnline nor FoLinn?)


[https://www.omc-stepperonline.com/h100-series-vfd-variable-frequency-drive H100 Series VFD Variable Frequency Drive]
[https://www.omc-stepperonline.com/h100-series-vfd-variable-frequency-drive H100 Series VFD Variable Frequency Drive]
Retrieved from "https://www.cncwiki.org/index.php?title=Folinn_H1_Series_VFDs"