Folinn H1 Series VFDs: Difference between revisions

← Older edit

@@ Line 19: / Line 19: @@
 == Model Numbers ==
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme
+In the FoLinn H1 series manual:
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme
+In the LinsVFD EV50 series manual:
+* [https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf#page=6 Page 6] (7 in the PDF) shows the model number scheme
 == Wiring Diagram ==
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=7 Page 7] (10 in the PDF) shows the power wiring
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=7 Page 7] (10 in the PDF) shows the power wiring
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=67 Page 67] (129 in the PDF) shows the H0101 interface panel screw terminal / RJ45 pinout
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=67 Page 67] (129 in the PDF) shows the H0101 interface panel screw terminal / RJ45 pinout
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=68 Page 68] (132 in the PDF) shows the H0110 interface panel screw terminal / RJ45 pinout
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=68 Page 68] (132 in the PDF) shows the H0110 interface panel screw terminal / RJ45 pinout
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=72 Page 72] (139 in the PDF) shows the H0100 interface panel screw terminal pinout
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=72 Page 72] (139 in the PDF) shows the H0100 interface panel screw terminal pinout
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=73 Page 73] (142 in the PDF) shows the H0200 interface panel screw / RJ45 / D-Sub? terminal pinout
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=73 Page 73] (142 in the PDF) shows the H0200 interface panel screw / RJ45 / D-Sub? terminal pinout
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=76 Page 76] (147 in the PDF) shows the H0201 interface panel screw / RJ45 / D-Sub? terminal pinout
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=76 Page 76] (147 in the PDF) shows the H0201 interface panel screw / RJ45 / D-Sub? terminal pinout
 NOTE: they claim that pins 1&amp;2 on the RJ45 are RS-485+/-, but in reality it's reversed and pins 8&amp;7 are RS-485+/- and pins 2&amp;4 are GND.
@@ Line 34: / Line 40: @@
 == Dimensions ==
-* [https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
+In the FoLinn H1 series manual:
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
+In the LinsVFD EV50 series manual:
+* [https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf#page=65 Page 65] (126 in the PDF) show a table of the dimensions
+== Parameters ==
+{| class="wikitable"
+! Parameter No.
+! Default Value
+! Range
+! Description
+|-
+| P02.18
+| 50.000 Hz
+| 0.000 - 99999.000 Hz
+| Maximum setting value
+|-
+| P02.19
+| 0.000 Hz
+| 0.000 - 99999.000 Hz
+| Minimum setting value
+|-
+| P02.50
+|
+| 0.050 - 3600.000 s
+| Acceleration time 0
+|-
+| P02.70
+|
+| 0.050 - 3600.000 s
+| Deceleration time 0
+|-
+| P05.08
+| 55.000 Hz
+| -1020.000 - 1020.000 Hz
+| Motor upper frequency limit
+|-
+| P06.00
+|
+| 0: off<br/>1: complete<br/>2: simple
+| Motor parameter self-learning
+|-
+| P06.10
+| 0: asynchronous
+| 0: asynchronous<br/>1: surface mount permanent magnet synchronous<br/>2: salient pole permanent magnet synchronous<br/>4: single-phase motor
+| Motor type
+|-
+| P06.05
+|
+| 2-16 kHz
+| Carrier frequency
+|-
+| P06.11
+|
+| 0.000 - 100000.000 kW
+| Motor rated power
+|-
+| P06.12
+|
+| 0 - 1000 V
+| Motor rated voltage
+|-
+| P06.13
+|
+| 1 - 3000 Hz
+| Motor rated frequency
+|-
+| P06.14
+|
+| 0.00 - 1000.00 A
+| Motor rated current
+|-
+| P06.15
+|
+| 10 - 65535 RPM
+| Motor rated speed
+|-
+| P06.16
+|
+| 0.00 - 1.00 (ratio)
+| Motor power factor
+|-
+| P06.17
+|
+| 2 - 100 poles (not pairs)
+| Motor pole count
+|-
+| P06.18
+|
+| 0.1 - 10000.0 Nm
+| Motor rated torque
+|-
+| P06.19
+|
+| 0.00 - 1000.00 A
+| Motor no-load current
+|-
+| P06.20
+|
+| 1.000 - 10000.000 mV/RPM
+| PM motor back EMF/rev
+|-
+| P06.40
+|
+| 0.000 - 99.990 ohms
+| Stator impedance
+|-
+| P06.41
+|
+| 0.000 - 99.990 ohms
+| Rotor impedance
+|-
+| P06.42
+|
+| 0.000 - 999.990 mH
+| Stator leakage reactance
+|-
+| P06.44
+|
+| 0.00 - 999.90 mH
+| Motor main reactance
+|}
+== Alarm Codes ==
+* [https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf#page=63 Page 63] (122 in the PDF) shows a list of fault codes
 == Modbus control ==
@@ Line 312: / Line 447: @@
 |-
 | P10.90
-| 0x8121
+| 0x0441
 | -999999.000 - 999999.000 %
 |
 | Set value 1
 |}
+NOTE: you add 0x4000 (16,384) to the addresses to go from 16-bit mode to 32-bit mode
+NOTE: you add 0x8000 (32,768) to the addresses to go from EEPROM to RAM access (important when writing frequently over MODBUS!)
 === mbpoll ===
+== PDFs ==
+[[Media:FoLinn_H1_Series_Inverter_User_Manual.pdf]]
 == Online Resources ==
-[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Full_User_Manual.pdf H1 Series Inverter User Manual (2021.V1.0)] (StepperOnline)
+[https://www.cncwiki.org/images/c/c1/FoLinn_H1_Series_Inverter_User_Manual.pdf H1 Series Inverter User Manual (2021.V1.0)] (StepperOnline, no FoLinn mentioned)
-[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Easy_User_Manual.pdf H1 Series Inverter Simple Manual] (StepperOnline)
+[https://www.omc-stepperonline.com/download/H1_Series_Inverter_Easy_User_Manual.pdf H1 Series Inverter Simple Manual] (StepperOnline, no FoLinn mentioned)
+[https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Full_User_Manual.pdf LinsVFD EV50 Series Inverter Full User Manual] (LinsVFD on StepperOnline, no FoLinn mentioned)
+[https://www.omc-stepperonline.com/index.php?route=product/product/get_file&file=3332/EV50_Series_Inverter_Easy_User_Manual.pdf LinsVFD EV50 Series Inverter Easy User Manual] (LinsVFD on StepperOnline, no FoLinn mentioned)
 [https://www.chinafolinn.com/uploads/image/20201021/5f8f9c43a68b0.pdf H1 Series Inverter Simple Manual (2020.10.21)] (Folinn)
@@ Line 332: / Line 477: @@
 [https://www.chinafolinn.com/uploads/image/20200602/5ed61f05888f9.pdf H1 Series Compact Inverter Brochure (2020.06.02)] (Folinn)
-https://cononmotor.com.au/wp-content/uploads/2022/05/2.29.182-H1-Detailed-Manual-%E8%8B%B1%E6%96%87%E7%89%88%E8%AF%A6%E7%BB%86%E8%AF%B4%E6%98%8E%E4%B9%A61.pdf
+[https://cononmotor.com.au/wp-content/uploads/2022/05/2.29.182-H1-Detailed-Manual-%E8%8B%B1%E6%96%87%E7%89%88%E8%AF%A6%E7%BB%86%E8%AF%B4%E6%98%8E%E4%B9%A61.pdf 2.29.182-H1-Detailed-Manual-英文版详细说明书1.pdf]
+[https://cononmotor.com.au/wp-content/uploads/2020/03/H1-Simple-User-Manual-Revised.pdf H1-Simple-User-Manual-Revised.pdf]
-https://cononmotor.com.au/wp-content/uploads/2020/03/H1-Simple-User-Manual-Revised.pdf
+[https://www.omc-stepperonline.com/linsvfd LinsVFD Variable Frequency Drives] (now LinsVFD branded instead of StepperOnline nor FoLinn?)
 [https://www.omc-stepperonline.com/h100-series-vfd-variable-frequency-drive H100 Series VFD Variable Frequency Drive]