AutomationDirect DURApulse GS20 Series VFDs: Difference between revisions

← Older edit

@@ Line 25: / Line 25: @@
 == Software ==
+[https://www.automationdirect.com/support/software-downloads?itemcode=GSoft2 Software & Firmware Downloads]
 GSOFT2 Drive Configuration Software
@@ Line 32: / Line 34: @@
 ! Size
 ! MD5
+! SHA1
+|-
+| [https://cdn.automationdirect.com/static/software/GSoft2_V2.0.2.1.zip GSoft2_V2.0.2.1.zip]
+| 252,209,721 bytes
+| 60aea9a1eac3ab52112fdaddcf61ea70
+| ac34673e94a6175bce5b0fa30ba203aeda8e638b
 |-
 | [https://cdn.automationdirect.com/static/software/gsoft2_v2.0.0.7.zip gsoft2_v2.0.0.7.zip]
 | 245,048,446 bytes
 | f274adb0afc390d777bdcfc624b7e17a
+| 02c591e95576d2e8180062f4f8b04d36ec478046
 |}
@@ Line 44: / Line 53: @@
 ! Size
 ! MD5
+! SHA1
 |-
 | [https://cdn.automationdirect.com/static/software/gslogic_v1.02.zip gslogic_v1.02.zip]
 | 28,959,436 bytes
 | 4f1ad6c07ecc4a88ca77ea89558caa29
+| c43013f34c64291d8c4b2ebfa4cbab2a1f68ff27
 |}
+== Parameters ==
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=89 Page 89] (4-3 in the PDF) has the parameter table
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=136 Page 139] (4-50 in the PDF) gives detailed descriptions of the parameters
+== Alarm Codes ==
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=384 Page 384] (6-8 in the PDF) list the warning codes
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=401 Page 401] (6-25 in the PDF) list the fault codes
+== Modbus control ==
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=359 Page 359] (5-1 in the PDF) is the chapter on "Serial Communications"
+=== VFD parameters ===
+{| class="wikitable"
+! Modbus Address
+! Parameter No.
+! Default Value
+! Required Value
+! Description
+|-
+| 0x0014
+| P00.20
+| 0: digital keypad
+| 1: RS-485 communication input
+| Master frequency command source
+|-
+| 0x0015
+| P00.21
+| 0: digital keypad
+| 2: RS-485 communication input
+| Operation command source
+|-
+| 0x0900
+| P09.00
+| 1
+| 1
+| Slave Address
+|-
+| 0x0901
+| P09.01
+| 9.6
+| 9.6
+| Baudrate
+|-
+| 0x0902
+| P09.02
+| 3: no warning, no fault, and continue operation
+| 2: fault and coast to stop
+| Communication Fault Handling
+|-
+| 0x0903
+| P09.03
+| 0.0
+| 2.0
+| Timeout Detection
+|-
+| 0x0904
+| P09.04
+| 15: 8, O, 1 (RTU)
+| 15: 8, O, 1 (RTU)
+| Communication Protocol
+|-
+| 0x0909
+| P09.09
+| 2.0
+| 2.0
+| Communication Response Delay
+|}
+From [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=360 Page 360] (5-2 in the PDF)
+=== Modbus registers ===
+* [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf#page=364 Page 364] (5-6 in the PDF) lists the status registers
+== Bill of Materials ==
+The microcontroller is marked:
+<pre>5F562TABDFP
+T?H303?60</pre>
+[https://www.digikey.com/en/products/detail/renesas-electronics-america-inc/R5F562TABDFP-11/13162670 Renesas R5F562TABDFP#11 | DigiKey]
+[https://www.mouser.com/ProductDetail/Renesas-Electronics/R5F562TABDFPV3?qs=ZVKuL1Ob8AsQxj8FF2um2Q%3D%3D Renesas R5F562TABDFP#V3 | Mouser]
 == Online Resources ==
 [https://www.automationdirect.com/drives/ac-drives/gs20 AC Drives GS20 and GS20X | AutomationDirect]
+[https://www.automationdirect.com/adc/shopping/catalog/drives_-a-_soft_starters/ac_variable_frequency_drives_(vfd)/general_purpose_vfds/gs23-45p0#docsanchor AutomationDirect DURApulse GS23-45P0 Downloads]
 [https://cdn.automationdirect.com/static/manuals/gs20m/gs20m.pdf AutomationDirect DURApulse GS20 & GS20X Drive User Manual (GS20_UMW, 1st Edition, Rev D)]