Siemens SIMODRIVE 1FT5 Servo Motors - Revision history

Fdarling: added 17-pin feedback connector pinout

2023-01-09T08:02:04Z

added 17-pin feedback connector pinout

← Older revision		Revision as of 08:02, 9 January 2023
Line 25:		Line 25:

	* [https://adegis.com/media/asset/30b9c1ad03b0990118f05b23a97806f7cec22564da96ef4dd4b4299463144cc2.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer, but with the pin names shown along with the numbers instead of a separate table.		* [https://adegis.com/media/asset/30b9c1ad03b0990118f05b23a97806f7cec22564da96ef4dd4b4299463144cc2.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer, but with the pin names shown along with the numbers instead of a separate table.

			=== 17-pin Feedback ===

			{\| class="wikitable"
			! Pin No.
			! Wire Color
			! Signal
			\|-
			\| A
			\| brown
			\| A+
			\|-
			\| B
			\| gray
			\| B+
			\|-
			\| C
			\| brown/green
			\| +5V
			\|-
			\| D
			\| green
			\| A-
			\|-
			\| E
			\| pink
			\| B-
			\|-
			\| F
			\| red
			\| Z+
			\|-
			\| G
			\| black
			\| Z-
			\|-
			\| H
			\| (shield)
			\| (shield)
			\|-
			\| J
			\| brown/green
			\| +5V
			\|-
			\| K
			\| brown/green
			\| +5V
			\|-
			\| L
			\| violet
			\| !fault
			\|-
			\| M
			\| (nc)
			\|
			\|-
			\| N
			\| white/green
			\| 0V
			\|-
			\| P
			\| white/green
			\| 0V
			\|-
			\| R
			\| black
			\| (jumper to S)
			\|-
			\| S
			\| black
			\| (jumper to R)
			\|-
			\| T
			\| white/green
			\| 0V
			\|}

			https://www.servotechusa.com/wp-content/uploads/2016/12/datasheet-Seimens-ROD-320-005.pdf

	== Dimensions ==		== Dimensions ==

Fdarling: added dimensions section

2022-12-31T21:50:43Z

added dimensions section

← Older revision		Revision as of 21:50, 31 December 2022
Line 25:		Line 25:

	* [https://adegis.com/media/asset/30b9c1ad03b0990118f05b23a97806f7cec22564da96ef4dd4b4299463144cc2.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer, but with the pin names shown along with the numbers instead of a separate table.		* [https://adegis.com/media/asset/30b9c1ad03b0990118f05b23a97806f7cec22564da96ef4dd4b4299463144cc2.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer, but with the pin names shown along with the numbers instead of a separate table.

			== Dimensions ==

			* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=157 Page 157] (1FT5/4-73 in the PDF) has the servo dimensional diagrams

	== Replacement Parts ==		== Replacement Parts ==

Fdarling: added hall sensor / tachometer pinout links

2021-01-27T05:32:41Z

added hall sensor / tachometer pinout links

← Older revision		Revision as of 05:32, 27 January 2021
Line 17:		Line 17:
	* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=588 Page 588] (GE1-6 in the PDF) shows the pinout diagram for the 17-pin connector for the "integrated encoder" (Heidenhain ROD 320 series).		* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=588 Page 588] (GE1-6 in the PDF) shows the pinout diagram for the 17-pin connector for the "integrated encoder" (Heidenhain ROD 320 series).
	* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=590 Page 590] (GE1-8 in the PDF) shows the pinout diagram for the 12-pin connector for the "mounted encoder" (Heidenhain ROD 426 series).		* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=590 Page 590] (GE1-8 in the PDF) shows the pinout diagram for the 12-pin connector for the "mounted encoder" (Heidenhain ROD 426 series).

			In the "Siemens Order No. 610.43 424.21.a" (?) document:

			* [https://cache.industry.siemens.com/dl/files/587/28689587/att_34824/v1/1FT502_BE_0993_de_en_fr_es_it_sv.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer feedback connector.

			In an alternate document:

			* [https://adegis.com/media/asset/30b9c1ad03b0990118f05b23a97806f7cec22564da96ef4dd4b4299463144cc2.pdf#page=8 Page 8] (2 in the PDF) shows the detailed pinout for the hall sensor/tachometer, but with the pin names shown along with the numbers instead of a separate table.

	== Replacement Parts ==		== Replacement Parts ==

Fdarling: added 12-pin encoder connector pinout link

2021-01-27T05:17:48Z

added 12-pin encoder connector pinout link

← Older revision		Revision as of 05:17, 27 January 2021
Line 13:		Line 13:
	In the "Siemens SIMODRIVE Planning Guide 11.2000 Edition AC Motors for Feed and Main Spindle Drives" (Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf) document:		In the "Siemens SIMODRIVE Planning Guide 11.2000 Edition AC Motors for Feed and Main Spindle Drives" (Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf) document:

	[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=52 Page 52] (ALS/4-42 in the PDF) shows the pin assignments for the various power connector sizes.		* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=52 Page 52] (ALS/4-42 in the PDF) shows the pin assignments for the various power connector sizes.
			* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=105 Page 105] (1FT5/1-22 in the PDF) has a general wiring diagram.
	[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=105 Page 105] (1FT5/1-22 in the PDF) has a general wiring diagram.		* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=588 Page 588] (GE1-6 in the PDF) shows the pinout diagram for the 17-pin connector for the "integrated encoder" (Heidenhain ROD 320 series).
			* [https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=590 Page 590] (GE1-8 in the PDF) shows the pinout diagram for the 12-pin connector for the "mounted encoder" (Heidenhain ROD 426 series).
	[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=588 Page 588] (GE1-6 in the PDF) shows the pinout diagram of the encoder connector.

	== Replacement Parts ==		== Replacement Parts ==

Fdarling: added 17-pin connector information

2020-04-23T14:11:49Z

added 17-pin connector information

← Older revision		Revision as of 14:11, 23 April 2020
Line 28:		Line 28:

	[[File:DigiKey_Part_889-2056-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-sine-systems-corp/MA7CAE1200S-S3-KIT/889-2056-ND/7692108 Amphenol MA7CAE1200S-S3-KIT]		[[File:DigiKey_Part_889-2056-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-sine-systems-corp/MA7CAE1200S-S3-KIT/889-2056-ND/7692108 Amphenol MA7CAE1200S-S3-KIT]

			=== 17-pin circular connector ===

			[[File:DigiKey_Part_97-3108B-20-29S-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-industrial-operations/97-3108B-20-29S/97-3108B-20-29S-ND/2510073 Amphenol 97-3108B-20-29S]

			[[File:DigiKey_Part_97-3057-1012-1-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-industrial-operations/97-3057-1012-1/97-3057-1012-1-ND/341011 Amphenol 97-3057-1012-1] (clamp and bushing)

			[[File:DigiKey_Part_97-3057-1012-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-industrial-operations/97-3057-1012/97-3057-1012-ND/341010 Amphenol 97-3057-1012] (clamp only)

			[[File:DigiKey_Part_97-79-513-12-ND.jpg\|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-industrial-operations/97-79-513-12/97-79-513-12-ND/341019 Amphenol 97-79-513-12] (bushing only)

	== Online Resources ==		== Online Resources ==

	[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf]		[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf]

Fdarling: initial page creation

2019-03-28T13:26:13Z

initial page creation

New page

== Overview ==

Servo motors made by Siemens.

== Model Numbers ==

In the "Siemens SIMODRIVE Planning Guide 11.2000 Edition AC Motors for Feed and Main Spindle Drives" (Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf) document:

[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=107 Page 107] shows the model number scheme ("Order Designation").

== Wiring Diagram ==

In the "Siemens SIMODRIVE Planning Guide 11.2000 Edition AC Motors for Feed and Main Spindle Drives" (Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf) document:

[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=52 Page 52] (ALS/4-42 in the PDF) shows the pin assignments for the various power connector sizes.

[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=105 Page 105] (1FT5/1-22 in the PDF) has a general wiring diagram.

[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide#page=588 Page 588] (GE1-6 in the PDF) shows the pinout diagram of the encoder connector.

== Replacement Parts ==

=== 4-pin power connector ===

[[File:DigiKey_Part_889-2088-ND.jpg|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-sine-systems-corp/MB7CKN0600-S3-KIT/889-2088-ND/7692140 Amphenol MB7CKN0600-S3-KIT]

=== 12-pin circular connector ===

[[File:DigiKey_Part_889-2056-ND.jpg|64x64px]] [https://www.digikey.com/product-detail/en/amphenol-sine-systems-corp/MA7CAE1200S-S3-KIT/889-2056-ND/7692108 Amphenol MA7CAE1200S-S3-KIT]

== Online Resources ==

[https://inverterdrive.com/file/Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide Siemens-1FT-SimoDrive-Servo-Motor-Planning-Guide.pdf]