Fuling DZB312 Series VFDs - Revision history

Fdarling: added more PDF links

2024-03-18T21:05:43Z

added more PDF links

← Older revision		Revision as of 21:05, 18 March 2024
Line 4:		Line 4:

	== Model Numbers ==		== Model Numbers ==

			In the DZB312 series manual:

	* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)		* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)

			In the DZB300 series manual:

			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=7 Page 7] (marked 7 in the PDF) shows the model number scheme
			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=8 Page 8] (marked 9 in the PDF) shows a table of model numbers and recommended component sizing
			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=47 Page 47] (marked 88 in the PDF) shows the specifications based off the model number ranges

	== Wiring Diagram ==		== Wiring Diagram ==

			In the DZB312 series manual:

	* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=5 Page 5] (marked 7 in the PDF)		* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=5 Page 5] (marked 7 in the PDF)

			In the DZB300 series manual:

			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=8 Page 8-9] (marked 10-11 in the PDF) shows an overview of the wiring
			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=9 Page 9] (marked 12 in the PDF) shows a the power terminal pinout
			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=10 Page 10] (marked 13 in the PDF) shows a the control terminal pinout

	== Dimensions ==		== Dimensions ==

			In the DZB312 series manual:

	* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)		* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)

	== ~~Modbus control~~ ==		In the DZB300 series manual:

			* https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=55 Page 55] (marked 104 in the PDF)

			== Parameters ==

			In the DZB312 series manual:

			* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=10 Page 10] (marked 18 in the PDF) shows the list of parameters

			In the DZB300 series manual:

			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=15 Page 15] (marked 23 in the PDF) shows the list of parameters
			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=21 Page 21] (marked 36 in the PDF) shows the detailed description of the parameters

	==~~= VFD parameters =~~==		== Fault Codes ==

	In the DZB312 series manual:		In the DZB312 series manual:

	* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=10 Page 10] (17 in the PDF) ~~gives~~ the ~~parameter list~~		* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=16 Page 16] (marked 29 in the PDF) shows a list of fault codes

			In the DZB300 series manual:

			* [https://www.cncwiki.org/images/a/a4/Fuling_DZB300_Series_Inverter_User_Manual.pdf#page=43 Page 43] (marked 79 in the PDF) has a flowchart for diagnosing issues

			== Modbus control ==

			=== VFD parameters ===

	~~Here are the ones~~ relevant for Modbus control:		Parameters relevant for Modbus control:

	{\| class="wikitable"		{\| class="wikitable"

Fdarling: added local copy of the DZB300/DZB200 manual

2021-08-27T03:19:58Z

added local copy of the DZB300/DZB200 manual

← Older revision		Revision as of 03:19, 27 August 2021
Line 251:		Line 251:

	[[Media:Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf]] (not available online?)		[[Media:Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf]] (not available online?)

			[[Media:Fuling_DZB300_Series_Inverter_User_Manual.pdf]]

	== Online Resources ==		== Online Resources ==

Fdarling: updated Modbus commands

2021-03-20T09:30:34Z

updated Modbus commands

← Older revision		Revision as of 09:30, 20 March 2021
Line 139:		Line 139:
	\| 0x2000		\| 0x2000
	\| 8192		\| 8192
	\| R/W ?		\| R/W
	\| -10000 - +100000 (frequency/PID percentage * 100)		\| -10000 - +100000 (frequency/PID percentage * 100)
	\| frequency/PID setpoint percentage ~~(?)~~		\| frequency/PID setpoint percentage
	\|-		\|-
	\| 0x3000		\| 0x3000
Line 170:		Line 170:
	\| 12292		\| 12292
	\| R		\| R
	\| ~~???~~		\| (rpm using parameter F1.03)
	\| output speed		\| output speed
	\|-		\|-
Line 182:		Line 182:
	\| 12294		\| 12294
	\| R		\| R
	\|		\| ???
	\| output torque		\| output torque
	\|-		\|-
Line 218:		Line 218:
	./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 2		./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 2

	# set the output frequency/PID percentage (percentage * 100)		# set the output frequency/rpm/PID percentage (percentage * 100)
	./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x2000 -t 4:int16 -- 10000		./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x2000 -t 4:int16 -- 10000

Line 238:		Line 238:
	# monitor output voltage		# monitor output voltage
	./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3003		./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3003

			# monitor output rpm
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3004

	# monitor inverter fault		# monitor inverter fault

Fdarling: updated setting speed

2021-03-20T09:15:35Z

updated setting speed

← Older revision		Revision as of 09:15, 20 March 2021
Line 218:		Line 218:
	./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 2		./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 2

	# set the output frequency		# set the output frequency/PID percentage (percentage * 100)
	./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x2000 -t 4:int16 -- ~~100~~		./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x2000 -t 4:int16 -- 10000

	# monitor command (whatever was previously written, can be invalid)		# monitor command (whatever was previously written, can be invalid)

Fdarling: added mbpoll commands

2021-03-20T09:12:17Z

added mbpoll commands

← Older revision		Revision as of 09:12, 20 March 2021
Line 140:		Line 140:
	\| 8192		\| 8192
	\| R/W ?		\| R/W ?
	\| ~~???~~		\| -10000 - +100000 (frequency/PID percentage * 100)
	\| frequency/PID setpoint percentage (?)		\| frequency/PID setpoint percentage (?)
	\|-		\|-
	\| 0x3000		\| 0x3000
	\| 12288		\| 12288
	\| R?		\| R
	\|		\| (decimal Hz * 10)
	\| frequency setpoint?		\| frequency setpoint
	\|-		\|-
	\| 0x3001		\| 0x3001
Line 158:		Line 158:
	\| 12290		\| 12290
	\| R		\| R
	\|		\| ???
	\| output current		\| output current
	\|-		\|-
Line 171:		Line 171:
	\| R		\| R
	\| ???		\| ???
	\| output speed?		\| output speed
	\|-		\|-
	\| 0x3005		\| 0x3005
Line 177:		Line 177:
	\| R		\| R
	\| ???		\| ???
	\| output power?		\| output power
	\|-		\|-
	\| 0x3006		\| 0x3006
Line 183:		Line 183:
	\| R		\| R
	\|		\|
	\| output torque?		\| output torque
	\|-		\|-
	\| 0x3007		\| 0x3007
Line 193:		Line 193:
	\| 0x5000		\| 0x5000
	\| 20480		\| 20480
	\| R?		\| R
	\| ???		\| ???
	\| inverter fault address?		\| inverter fault address
	\|-		\|-
	\| 0x5001		\| 0x5001
Line 203:		Line 203:
	\| Modbus communication fault		\| Modbus communication fault
	\|}		\|}

			=== mbpoll ===

			<pre># fault reset (need to test)
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 7

			# stop
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 5

			# set forward run
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 1

			# set reverse run
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000 -t 4:int16 -- 2

			# set the output frequency
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x2000 -t 4:int16 -- 100

			# monitor command (whatever was previously written, can be invalid)
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1000

			# monitor inverter status
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x1001

			# monitor commanded frequency
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3000

			# monitor output frequency
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3001

			# monitor output current
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3002

			# monitor output voltage
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x3003

			# monitor inverter fault
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x5000

			# monitor Modbus communication fault
			./mbpoll /dev/ttyUSB0 -b 9600 -s 1 -P none -a 1 -0 -r 0x5001</pre>

	== PDFs ==		== PDFs ==

Fdarling: added Modbus register table

2021-03-20T08:25:45Z

added Modbus register table

@@ Line 117: / Line 117: @@
 * [http://www.chinafolinn.com/uploads/image/20200602/5ed6233f8b4eb.pdf#page=49 Page 49] (91 in the PDF) describes the Modbus protocol (should be standards compliant)
 * [http://www.chinafolinn.com/uploads/image/20200602/5ed6233f8b4eb.pdf#page=53 Page 53] (100 in the PDF) has the register address map
 == PDFs ==

Fdarling: added more Modbus information

2021-03-19T20:58:07Z

added more Modbus information

@@ Line 17: / Line 17: @@
 == Modbus control ==
-DZB300 manual applies to DZB312 for Modbus information.
+=== VFD parameters ===
 == PDFs ==

Fdarling: initial page creation

2021-03-14T19:10:06Z

initial page creation

New page

== Overview ==

Variable frequency drives specialized for CNC router spindles. The drives are made by Fuling Electric, aka Folinn Electric.

== Model Numbers ==

* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)

== Wiring Diagram ==

* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=5 Page 5] (marked 7 in the PDF)

== Dimensions ==

* [https://www.cncwiki.org/images/f/f9/Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf#page=18 Page 18] (marked 33 in the PDF)

== Modbus control ==

DZB300 manual applies to DZB312 for Modbus information.

== PDFs ==

[[Media:Fuling_DZB312_Series_Carving_Machine_Inverter_User_Manual.pdf]] (not available online?)

== Online Resources ==

[http://www.chinafolinn.com/trait-202.html DZB312 Series Engraving Machine Special Inverter_ZHEJIANG NEW FOLINN ELECTRIC CO.,LTD]

[http://www.chinafuling.com/trait-196.html DZB312变频器-DZB312系列雕刻机专用变频器-浙江新富凌电气股份有限公司] (Chinese version of above link)

[http://www.chinafolinn.com/trait-192.html DZB300 Series General Vector Inverter_ZHEJIANG NEW FOLINN ELECTRIC CO.,LTD]

[http://www.chinafuling.com/trait-194.html DZB300变频器-DZB300系列通用矢量型变频器-浙江新富凌电气股份有限公司] (Chinese version of above link)

http://www.chinafuling.com/uploads/image/20200602/5ed609046fdd7.pdf (DZB312 series manual in Chinese)

http://www.chinafolinn.com/uploads/image/20200602/5ed6233f8b4eb.pdf (DZB300 series manual in English)

http://www.chinafuling.com/uploads/image/20200602/5ed6078d6dfde.pdf (DZB300 series manual in Chinese)

[http://www.chinafolinn.com/ Home_ZHEJIANG NEW FOLINN ELECTRIC CO.,LTD] (English website)

[http://www.chinafuling.com/ 富凌官网-变频器-伺服驱动-主轴电机-全国统一服务热线：400-889-7111] (Chinese website)